How To Put Line In A Oregon Battery Power Weedeater

Eugene is an avid gardener and has been passionate near growing things for over twoscore years.

Gas and electric corded trimmers

© Eugene Brennan

What Is a String Trimmer?

This garden power tool has many names depending on where you live in the world, but one affair is sure: It certainly beats a hedge shears for trimming and edging! Like most power tools nowadays, string trimmers are available in gas, electrical corded and rechargeable battery cordless versions.

The machine was invented in the early 1970s past George Ballas of Houston, Texas. He attached fishing line to the head of a lawn edger and was able to cut grass and weeds with his concoction. The tool works on the principle that a line spun at high speed becomes stretched and taut due to centripetal dispatch. The tension in the line makes it stiff, and the inertia of the line gives it the energy to cutting. So basically, it is like a spinning whip.

This guide shows y'all how to wind the spool and cut, without breaking the line!

Alternative Names for a String Trimmer

A string trimmer is also known as:

Weed Eater (brand name)
Weed Whacker
Strimmer (In the UK and Ireland)
Weed Trimmer
Lawn Trimmer
Weed Whip
Whipper Snipper (Commonwealth of australia and Canada)
Line Trimmer

How to Use a String Trimmer Safely

Follow these safety tips in order to operate your string trimmer properly.

Wearable PPE (Personal Protective Equipment)

The most important thing is to protect your optics because even a small piece of snapped line, or debris such as a pebble travelling at 200 to 300 mph has the potential to crusade a severe center injury. A visor provides full face protection.
Don't wear shorts or sandals for obvious reasons. Heavy trousers will give some protection if you get hitting past debris (fifty-fifty though you will still feel information technology!). Even cleaved off fragments of trimmer line will cut pare.
Wearable safety shoes which take steel caps and soles, as these volition protect your feet if you walk on glass, metallic, nails or other nasty stuff while working in an overgrown area. When cut, angle the trimmer so that cut material is thrown away from yous.
Finally, wear ear muffs to protect your ears as long term exposure to loud sounds tin cause hearing damage.

Check the Footing Earlier Trimming

$.25 of glass, metallic, pebbles etc. tin can be defenseless past the line and become missiles

Take Care of Cables

Take care non to striking the cable while using an electrical trimmer. Electrical trimmers are less powerful than gas versions and the line probably wouldn't cut the cord, however information technology could impairment the insulation.

Scout Out for Bystanders

People standing near you lot are more likely to be hit by debris than yourself. This is because debris may be travelling on an upwards trajectory and eventually attain eye level past the time it reaches the other person. This is especially the example if you are trimming or using a lawn mower on elevated ground. So pause your work until they have moved away.

Debris thrown by a trimmer can also ricochet off difficult surfaces. Immature children should never be in the vicinity when you are using powered garden equipment.

Avoid Windows and Cars

Pebbles thrown by a trimmer tin easily chip paintwork and drinking glass, and may even crack or break windows in your house or automobile. Bank check where droppings is flying and direct information technology safely away from anything which could be damaged

How to Mix Fuel for a Gas Trimmer

Well-nigh trimmers have two stroke engines which don't accept a sump filled with oil for lubrication (iv stroke trimmers however are available). So lubricating oil must be mixed with gas before filling the tank.

Gas and 2-Stroke Oil Needed for a l:1 Ratio

For a 25:i ratio, double the amount of oil
Amount of Fuel Mixture Required	Gasoline/Petrol	Ii Stroke Oil
1 Litre	1 Litre	20 ml
five Litres	v Litres	100 ml
1 US Quart	ane Us Quart	0.six Us Fluid Ounces
1 United states Gallon	1 U.s.a. Gallon	2.six US Fluid Ounces

How to Offset a String Trimmer

A general process for starting two-stroke engines. There may exist some variation as regards setting choke positions, and then consult the instructions that came with your auto.

Mix fuel as outlined in a higher place and fill the tank at to the lowest degree half full.
Turn on the ignition switch.
Plough on the choke.
Prime number the engine by pushing the primer button about 8 times.
Pull the starter cord repeatedly until the engine kicks and attempts to beginning or runs.
If information technology runs, allow it to continue running for virtually 10 seconds and then turn off the choke.
If it cut out with the choke on, try turning off the choke and re-pulling the string. If it doesn't get-go afterwards a few attempts, turn the choke back on and re-starting.

What If I Can't Outset the Engine?

If you lot nonetheless can't start the engine, check out my mistake-finding guide to string trimmers: String Trimmer (Strimmer) Won't Work: 2-Stroke Engine and Carburetor Troubleshooting

What Blazon of Line Do I Utilise With My Trimmer?

Trimmers brand use of a monofilament nylon line for cut. You can buy this line in spools or rolls of varying lengths and cutting information technology to size. Lower powered electrical trimmers are normally used with fairly light gage line, about 1.5 mm / 0.06 inch (virtually 1/xvi inch). This is fine for trimming light grass growth around curbs, edges of lawns and flower beds.

Higher powered gas trimmers can as well be used with light cuff line, but for cut thick vegetation in overgrown areas such every bit long grass, nettles, docks and other weeds, heavier gage line is pretty much essential to avoid breaking or tangling the line. This is available in sizes up to 4 mm / 0.xvi inch (well-nigh iii/sixteen inch ). You can as well buy line which has a foursquare profile rather than round, and supposedly the "corners" cut better.

What I Employ

I use a two.4 mm line (almost 0.i inch) with my gas trimmer, which is a depression cc model, and it gives proficient results with calorie-free and small amounts of heavy growth. Thicker cuff line requires a correspondingly higher powered trimmer so that the head can spin sufficiently fast without the engine struggling and slowing down in thick vegetation. Every bit e'er, its better to consult your manual to see what the manufacturer recommends.

Trimmer Line Replacement: Winding the Spool

Make sure the end of the line is fully attached to the spool by feeding information technology through the thread hole or guide designed for this purpose. The line should then be wound tightly and evenly around the spool in the direction of the arrow (pull the line tight to tension it as you are doing and so).
If the line is wound slackly, excess line volition feed out of the spool during an auto feed, or when you bump the cutting caput to release line, and just terminate up getting snapped off by the knife on the guard of the trimmer. Corking winding helps to ensure that line feeds out ok and doesn't bind. You don't have to exist overly fussy well-nigh this. Simply brand sure all the line isn't bunched up at i end of the spool or is very loosely wound around it.

Photo Tutorial

Thread the end of the line into the hole and wind it in the management of the arrow.

Evenly wound spool. You can wind on lots more than line than this.

String trimmer line on spool

© Eugene Brennan

Supervene upon the spool into the cutting caput. Feed the end of the line through the hole in the cutting caput of the trimmer and replace the cap.

Feed the line through the hole in the cutter head

© Eugene Brennan

Replace the cap on the cutting head (if fitted).

How to Supersede a String Trimmer Line

The Cutting Knife on a Trimmer

With some trimmers, the cut head must exist bumped down onto the ground to release new line. Other models auto-feed as line is used up. In any instance, a cut knife at the perimeter of the guard on the trimmer keeps the line trimmed and prevents information technology hitting or extending beyond the guard (which will irksome or stall the machine and create a hazard). This knife should exist sharp, otherwise it won't cut the line. If you discover this problem, you can sharpen it with a file, sharpening stone, or bending grinder.

Cutting knife on trimmer

© Eugene Brennan

Long-Lasting Square Trimmer Line

This 0.095 inch bore (2.4mm), three pound, 685 human foot spool of professional person trimming line manufactured by Oregon and available from Amazon should last you years and years. Information technology has a loftier strength inner cadre and an outer coating to prevent welding. In other words information technology is less likely to stick every bit it unwinds from the spool. The foursquare edges also ameliorate cutting efficiency compared to standard round contour type.

Check your trimmer to see whether information technology is compatible with this diameter line.

How to Cutting With a Trimmer

When using an electrical trimmer, cut with the bare tip of the line because this is the section which moves at the highest speed
Don't let the line slap into grass. Ease the line into vegetation, chip by flake from the border. You shouldn't allow all the line to come in contact with grass as this will tend to wearisome information technology down causing information technology to lose momentum and it won't practice a good job of cutting
When cutting around thick vegetation, it's vital to slowly move the line into the material being cutting, otherwise it'll become tangled or break. A gas trimmer has more than power, is usually fitted with heavier gage line, and you can allow more of the line into the vegetation without it slowing downwards. You just need to listen to the sound of the automobile and when the line slows down, dorsum off out of the grass
The line frequently breaks when trimming around pavements, kerbs, pots etc, This is because it tends to slap confronting the difficult surface instead of soft growth and this can shear or abrade it rapidly. This is why it is important to only cut with the tip of the line. It still wears apace, but just a little bit at a time rather than in large pieces
Thinner gage line will snap more readily. You can use a thicker line just it is less constructive when cutting at low speeds. The advantage of a gas trimmer is that you lot can vary the speed depending on whether y'all are cut fine grass or thick vegetation
When cutting, angle the trimmer so that the cutting head isn't rubbing off the footing. Accommodate the distance of the head from the ground so that the full extent of the line isn't rubbing off the ground surface either. Allow the tip of the line exercise the work and ease it into the area beingness cutting
When cut around shrubs and trees, have intendance you don't strip the bawl which can kill the found
Creepers and climbing plants tin sometimes get tangled around the cut head of a trimmer, although the line usually cuts through these, nevertheless if you lot accept young cabbage palms (cordylines) in your garden, go on well away from the leaves! These are long tough and stringy and always seem to get wrapped effectually the head, stalling the engine

Cutting with the tip of the line to avoid breaking it — Cut with the tip of the line to avoid breaking it

© Eugene Brennan

Angle the trimmer when cutting

© Eugene Brennan

Lighter Gage Line for Gas or Electrical Trimmers

Home-possessor grade trimmer line by Rino-Tuff from Amazon. This line is lighter cuff 0.065 inch (ane.65 mm) and more suitable for electrical trimmers. You can use it with a gas trimmer, but information technology will snap and get used upward quicker when cutting heavier vegetation. Thinner line is more suitable for cutting light growth and trimming around flower beds and curbs.

Bank check your trimmer documentation to ensure this diameter line is suitable.

How to Avert Getting Covered by Grass

The line more often than not turns clockwise (viewed from above), so when information technology's to right of the cutting head it'southward heading towards you and when on the left, it heading away from yous. If y'all imagine a circle through which the line turns, try to go on this circle positioned and so that you're cutting in the x o'clock to 12 o'clock positions and grass is being thrown away from yous or perpendicular to you.

How to reduce the amount of grass thrown back towards you.

© Eugene Brennan

Edging a Flower Bed

I maintain a sort of "kerb(adjourn)" effect at the edges of my flower beds, and the soil is lower than the backyard and slopes upwards and backwards (see photo below). This makes it easy to trim the grass at the edge of the lawn when it gets ragged. In this instance, the trimmer is first used in the normal horizontal mode to taper the grass level to the border of the bed, which looks amend. Next switch to vertical mode so that the line is perpendicular to the ground every bit shown in the video below.

How to edge a lawn with a trimmer. — How to border a lawn with a trimmer.

© Eugene Brennan

Lawn edge maintained with a trimmer — Backyard edge maintained with a trimmer

© Eugene Brennan

A lawn edged with a trimmer

© Eugene Brennan

Using Electric and Gas Trimmers

Which is Best? An Electric or Gas Trimmer?

Gas (Petrol) trimmers have traditionally been more powerful and convenient to use than corded electric trimmers, however bombardment trimmers offering several advantages:

No issues trying to start the engine. They work instantly
No fumes or toxic emissions, so they're meliorate for the environment
Battery technology has improved and then trimmers can work longer on a accuse
No cord to cut or trip over
Less noise than a gas trimmer
Newer models have the motor at the top of the handle, so ameliorate balanced

Choosing and Ownership a Cord Trimmer

Trimmers are produced past all the well known tool manufacturers. This includes Black & Decker, Qualcast, Flymo, Stihl, Husqvarna and many more. Although ownership a well known brand doesn't necessarily guarantee a reliable or durable product, it does mean that spare parts are more than easily sourced.
Your choices are gas, electrical or battery (cordless). In general gas powered models are more powerful, but loftier powered electrical models are also available such equally the Greenworks 21142.

Greenworks 21142 string trimmer.

Amazon

Recommended Trimmer: Greenworks 21142

Greenworks 21142 model. This has a ten amp motor (equivalent to over 1100 watt or 1 1/two HP). The reason I like this machine is because the motor is mounted virtually the handle end of the shaft different lower powered corded electric trimmers that have the motor at the cut head. This balances the machine amend. Because it's electric in that location are no fumes and it's ideal if you yous detect information technology difficult to pull start an engine. See also the annotate by Dennis beneath.

This article is authentic and truthful to the best of the author's knowledge. Content is for informational or entertainment purposes just and does not substitute for personal counsel or professional advice in business, fiscal, legal, or technical matters.

Questions & Answers

Question: My make new trimmer becomes very hot in a few minutes and and then stops abruptly. When I restart it once again functions just if I begin to cut again information technology stops and doesn't cut. It can but start simply cannot cut. Please, what causes this? It is a brand new, and I've used it twice, only the same trouble occurred.

Reply: Firstly, if information technology'southward brand new, bring it back or send information technology back if you bought it online, because it'll be on warranty for probably a twelvemonth.

If you're trying to trim long grass, try not to push the trimmer too far into the grass as it can overload the motorcar and tangle upwardly the head.

Is this a petrol/gas machine? If and then you demand to use two stroke oil at a ratio of one office oil to 50 parts gas to lubricate the machine and finish information technology overheating and seizing up.

If the trimmer is electric, is information technology suited to your voltage supply? A 110-volt trimmer used on a 240 volt supply will overheat and burn down out or if you lot're lucky an overcurrent circuit breaker device on the tool volition cut off power before this happens.

Question: How to pull the string out when it is cutting?

Respond: If y'all mean the cord, checkout this guide whic shows you how to replace the cord:

https://dengarden.com/habitation-comeback/Stihl-KM-56...

Question: Why does the nylon line get longer when using a string trimmer?

Answer: If the trimmer auto feeds, it's possible that the machinery is faulty and letting the line out too chop-chop. The cutter on the trimmer guard should cut the line in any case. Try winding the line a bit tighter and neater on the spool because if information technology's loose, it will feed out besides much.

Question: Can you use a string trimmer for cutting overgrown grass that's two feet tall?

Answer: Yes, you can cut any elevation of grass. Nevertheless, information technology's important not to overload the trimmer if it's low powered. Long grass may tend to tangle in the head and then cut a bit a little at a time by moving the tip of the line slowly into the grass. Don't bury information technology in growth. Articulate the waste product out of the fashion as you lot piece of work if you detect it's tangling upwards in the cut head.

Question: How much two stroke oil do I mix with petrol for my trimmer?

Respond: In full general, mix 1 part oil with 50 parts petrol (gas). However, some manufacturers recommend that you mix 1 part oil with 25 parts petrol. Consult your manual for details.

Question: Caput of a Stihl string trimmer stops moving and makes a bad noise. What could be the problem?

Answer: It could be a couple of things. Possibly the clutch is worn or the clutch springs have broken. The clutch is located upwardly near the engine. Too, the drive shaft may accept cleaved or the section where the shaft joins with the head could be damaged.

Question: How do I preclude line fusion of a string trimmer?

Respond: Endeavour and wind the line tight and evenly. I've never tried it, but yous could try spraying the windings with silicone spray. It's expert for freeing hooks/rings on curtain rails, so it might as well work for trimmer line.

Eugene Brennan (author) from Republic of ireland on July 25, 2019:

Turning a motor on and off causes a surge of current into the motor, plus over fourth dimension arcing of the switch contacts in the trigger can cause arcing and deposition of the switch. The chances though are that the bearing on the trimmer head (at the end of the shaft) volition vesture out before this happens. The insulating varnish on the windings of the rotating armature inside the motor also breaks down over fourth dimension, eventually resulting in the motor burning out. And then it'due south hard to tell really what the best choice, probably doesn't make much difference.

The Deardorff on July 24, 2019:

My stride son uses the electric weed wacker, by starting and stopping the engine constantly. Is this skillful to practice, or should he go on the line moving at a steady stride?

Eugene Brennan (writer) from Republic of ireland on June 21, 2019:

Hi Tim,

When y'all feed the line through the hole with one manus, hold it with your other hand. Put the cover back on the reel holder (if in that location is one) While still property the finish of the line, push button the reel holder cover in every bit if you're doing a crash-land feed and pull more line out and then release it. Alternatively simply feed more line through the hole when you supercede the reel and then that it doesn't all go back through the pigsty when tension is released.

Tim Jones IA on June 21, 2019:

The string trimmer I use keeps having problems. I wrap new line (have tried numerous types) effectually the spool but when I feed it through the hole, all the tension in the line is released and the line snaps dorsum through the pigsty. How practice I keep sufficient tension on the spool on the line?

Matthew on May 29, 2019:

Why practice you retrieve the gasoline string lawn trimmers practise not have the engine cylinder and engine cylinder head as ane slice or have the caput thread onto the cylinder?

Eugene Brennan (author) from Republic of ireland on May 28, 2019:

There all the same might be more stringy vegetation caught betwixt the dorsum of the head that houses the spool of line and the shaft of the weed eater. Await in from the side without the guard and you should exist able to come across it. Yous could poke information technology out with a long sparse screwdriver, opened out wire coat hanger or like. If at that place isn't anything caught, the head may accept been damaged.

Crystal Shaver on May 28, 2019:

When I was weed eating on Monday, I was cutting down some high weeds with my weed eater, when a bunch of them got wounded up on the weed eater I had to cut the weeds to remove them from the weed eater. Then when i started it back upwardly it had a difficult fourth dimension spinning. So I turned information technology off so it could cool down.

What should I practice when I outset information technology support again and it has a hard time turning?

Eugene Brennan (author) from Ireland on May 11, 2019:

Hullo Ger,

Mine is a Procut model (Woodies own brand) with crash-land feed, so the caput has to be bumped on the footing to let out line. Is yours the same or is it supposed to auto feed as the line shortens? The only affair I tin can suggest is to try and keep the winding neat with turns adjacent as yous wind, so put your finger on the terminate of the line to stop the turns unravelling every bit you lot supervene upon the spool into the head. Then pull the line tight out of the hole. Occasionally side by side turns tin bind and line not feed out but it doesn't happen regularly. Make sure the spool is seated properly in the head before you screw on the embrace.

GerOBrien on May 11, 2019:

Hi, Eugene, not sure if your still responding to comments but here goes.

I bought a 2 stroke petrol strimmer today and later a few minutes of strimming, the line stops car feeding. When I open the head the line gets caught around itself. I've tried to steps of coiling the line upward in the direction of the arrows and tightly merely all the same information technology keeps happeningp? Whatever thoughts?

It'due south a procut 26cc model, line trimmer.

Sharon on March 03, 2019:

Everytime I weed consume the string breaks. I have to terminate take the string out and put back in. I hate weed eaters.

Eugene Brennan (author) from Republic of ireland on February 16, 2019:

Cheers Geraldine. Some vegetation can be very tough with stringy fibres and a trimmer won't cut it, although a brush cutter, mayhap one with a cutting disk, will exercise. The leaves of cordylines are really awful and will tangle up a trimmer line and wrap themselves around the head.

Geraldine on February 16, 2019:

Thankyou Eugene. The string on my flymo trimmer keeps flying out. Possibly the Elephant grass is too stiff for it Will also try and tie string tighter. I have a Ryobi trimmer but the giddy string is stuck! Husbands shouldnt die before wives!! Geraldine South Africa

Eugene Brennan (author) from Ireland on September 26, 2018:

Try winding the spool tighter.

Bank check the finish of the line is securely attached to the spool before yous wind.

The mechanism that releases the line (if it atofeeds or line tin be fed out by bumping the head) may be damaged.

Bank check the spool is seated properly inside whatsoever outer enclosure that the line passes through.

Tom Wells on September 26, 2018:

Line comes out of the spool when running,

Eugene Brennan (author) from Ireland on September 12, 2018:

Not bad! Thanks for sharing the info! These comments practice aid.

Fake Name on September 12, 2018:

I figured out why the line was hit the guard. My trimmer's guard lost two of the 3 screws holding it in place, and it made the guard hang just a niggling scrap also depression. Bought a couple screws from the local hardware shop for a few cents, installed them, and I don't dread doing yard piece of work anymore! Hope it helps somebody in the hereafter! Thanks for the help!

Eugene Brennan (author) from Ireland on August 31, 2018:

Hullo Jeanette

Does the string motorcar feed? I presume you've tried to wind information technology tight and even every bit suggested, and so backlog line doesn't fly out and get cut off when it feeds. Have you lot wound it in the right direction effectually the spool? Usually there'due south an pointer indicating which way to wind. Also utilise a heavy enough gauge of string equally recommended by Stihl. Low-cal gauge line wears and snaps quicker. The just other think I can retrieve of is that something's gone amiss with the feed machinery.

Jeanette on Baronial 31, 2018:

Hullo Eugene: Good article. Question: I have a heavier duty stihl. The lower string breaks quite speedily. It doesn't matter if I am going fast or slow, in heavy vegetation or low-cal. I finish up with a lot of the lower second cord yet on the spool, when the superlative is gone, and more often than not, I'one thousand cutting with one string. Two strings would be better. I haven't found anything obvious that would be cutting the string. Suggestions?

Eugene Brennan (author) from Ireland on August 24, 2018:

The line should exist on the same plane as the cutter so that it'll always cut information technology.

Fake nam on Baronial 24, 2018:

What if the line points upwards, and hits the baby-sit? The line is already shorter than the cutter can attain.

Eugene Brennan (author) from Ireland on June 12, 2018:

There should be a cutter on the edge of the guard that trims it to size.

If you lot discover that the line is e'er flight out and striking the guard, information technology may be also loosely wound on the spool. When winding, try to keep it fifty-fifty plus wind tightly every bit shown in the video.

Antwan Alvarado on June 12, 2018:

The line keeps hitting with the plastic baby-sit and makes an awful dissonance. is that good?

Eugene Brennan (author) from Republic of ireland on July 04, 2017:

Y'all could use a brushcutter. These are fitted with metal or plastic cutting flails (although flails are banned in the EU http://world wide web.hse.gov.uk/safetybulletins/brush-cutter...

Some brushcutters are fitted with circular saw blades, brush knives, grass blades, etc.

These cut heads are suitable for cutting castor growth, i.east. thick woody stems. I don't know how effective they would exist on grass and it'due south unlikely they could be used upwards shut to herbs.

Majid Buchh on July 03, 2017:

Howdy there. I would like to know if in that location is whatsoever trimmer I can buy without having to go through strings. Do gas ones have these things?

Is there such matter a trimmer without strings. Like let'south say stringless

Dennis on June 10, 2017:

I never had a gas trimmer outclass my greenworks 21142 at all. Quite the opposite. Even won a $100 bet against a gas i. When they effigy how to brand a battery powered 1 perform like a 10 amp corded trimmer with run time of gas, then gas trimmers will be a dead market.

Eugene Brennan (writer) from Ireland on September eighteen, 2016:

How-do-you-do John, I never thought of doing that because I've never had trouble with binding. Nylon is used for trimmer line considering of its two desirable characteristics, high resistance to chafe and low friction coefficient (i.eastward. it'due south slippery). If the line binds, it could exist considering the turns on the spool are wound too closely together. When winding, I try to space the turns widely rather than packing them closely together. However try to pull the line tight equally you wind the spool to prevent excessive line feeding out as the caput spins.

I don't know whether oiling the line would be constructive just you could attempt using a silicone spray which would exist less messy than oil. However it'due south likely that centrifugal force would just throw lubricant off the coils as the caput spins.

John on September 17, 2016:

Practise you lot ever oil your trimmer line to prevent bounden? Thanks.

Eugene Brennan (author) from Ireland on August 11, 2016:

Hi Len, as outlined in the commodity above, try to cut with the tip of the line, don't bury it in vegetation or let it slap off concrete. Don't allow it wrap around shrubs and basically simply ease information technology into vegetation when cutting. Sparse line volition wear and quicker when attempting to cut dense vegetation with an electric trimmer so just take information technology like shooting fish in a barrel with it or try using a thicker line. I take used two.4 mm (about 0.1") line with my Black and Decker and it lasts longer when cut dumbo growth, even so long term the heavier weight of the line probably isn't the best for the bearing of the machine (considering it puts more than load on it).

Len on August 11, 2016:

The line of my weed eater keeps breaking any ideas

Eugene Brennan (author) from Ireland on October 29, 2015:

Thanks Jodah, information technology can be frustrating when the line breaks, which is often due to over zealous use of the auto. Watch out for shrubs and trees also, the line can easily strip bawl and stunt growth.

John Hansen from Gondwana State on Oct 28, 2015:

This was a very useful commodity eugbug. It drive me around the twist having to continually supercede line in my trimmer. I volition accept your advice and take more intendance to only employ the cut tip of the line and move into grass slowly a little at a fourth dimension.

Neelakantan on May 29, 2015:

The commodity is well written and easy to sympathize. It is well illustrated with photographs. The author is very sincere and defended. Wish him/her good luck

Michael M. Rodriguez from Orlando on October 25, 2014:

Likewise keen. Your article was so adept and sufficient

Terry on August 08, 2014:

Fabulous instructions and photos. Best web pages I have seen showing so much detail, of tremendous assist to me. Thanks.

Judy Specht from California on March 31, 2013:

I tin can't ever get the string to crash-land properly. Thanks for helping with the angles.

Eugene Brennan (author) from Republic of ireland on March 31, 2013:

How-do-you-do tamron, thanks for the comments and dropping by!

tamron on March 31, 2013:

Well illustrated hub with easy to follow instructions for weed eating!

Eugene Brennan (author) from Ireland on March 31, 2013:

Hi John. Thanks for the comment. Nosotros don't have to worry about grass cut or trimming yet here. There's no growth notwithstanding because we're getting blasted in northern Europe by common cold due east winds from Siberia for the terminal calendar month.

John MacNab from the banks of the St. Lawrence on March 31, 2013:

A practical guide to trimming, eugbug. Thanks - yous published it at the right time - when I'm looking for my trimmer in an overcrowded shed.

Source: https://dengarden.com/landscaping/How-to-Use-a-String-Trimmer-Properly

Posted by: starkuplithim98.blogspot.com